Safety<\/a> always comes first. And to that end, you should avoid working with anything while it\u2019s connected to the electricity. And more so when your work involves water.<\/p>\n\n\n\nStart by shutting off the power switch of the pump, then flip the circuit-breaker of the pump to the off position, and finally shut down the pool system circuit-breaker. This should let you carry out the necessary adjustments under safe working conditions.<\/p>\n\n\n\n
Step 2: Take the Lid Off the Pump<\/h3>\n\n\n\n The lid might feel a bit stuck at first, but it\u2019s not. It\u2019s supposed to be closely screwed into place. That\u2019s because the water should be flowing in a leak-tight system, and a wiggly cover would blow that right away.<\/p>\n\n\n\n
You might need to use a little tool to help you out. But usually, it starts moving after a couple of attempts.<\/p>\n\n\n\n
Now is a good time to inspect the lid for cracks, holes, or hairline fractures. Also, you can wash it and rinse the gasket. Leave all the parts to dry while you work on the next steps.<\/p>\n\n\n\n
Step 3: Set the Multiport Valve to \u2018Recirculate\u2019<\/h3>\n\n\n\n This step is absolutely necessary so make sure to do it right.<\/p>\n\n\n\n
The multiport valve is usually not located on the pump itself but installed on the pipes right beside it. When you find it, you\u2019ll notice that there are several settings like rinse, winter, backwash, and recirculate.<\/p>\n\n\n\n
Choose the \u2018recirculate\u2019 option, which keeps the flow of water away from the filter, and strictly inside the pump.<\/p>\n\n\n\n
Step 4: Open the Air Valve<\/h3>\n\n\n\n Pool Pumps aren\u2019t fond of air at all. And any amount of trapped air inside them can make the whole process go haywire. That\u2019s why you\u2019d often find air vents in such systems to let out any trapped bubbles. Also, to facilitate priming the pump and filling it up with water.<\/p>\n\n\n\n
Locate the air valve on the filter. It\u2019s often a little knob or nozzle, and you\u2019d often find a pressure gauge beside it.<\/p>\n\n\n\n
Turn this knob counterclockwise and keep it fully opened. At this point, the pressure gauge should read 0 PSI.<\/p>\n\n\n\n
Step 5: Clean up the Pump\u2019s Basket<\/h3>\n\n\n\n It\u2019s customary to find debris and accumulated particulate matter in the basket. Before operating it, check that the basket is in mint condition and that it\u2019s fully cleaned up.<\/p>\n\n\n\n
Put it back where it came from, and make sure that it\u2019s sitting properly in its place.<\/p>\n\n\n\n
Step 6: Fill Up the Pump With Clean Water<\/h3>\n\n\n\n The pump can only work if there\u2019s water inside it and inside the piping system connected to it. You can use a garden hose or bucket to fill up the system with water. Keep at it until the drains start spewing out water.<\/p>\n\n\n\n
Once the pump is full, you should screw the lid tightly back into place.<\/p>\n\n\n\n
Step 7: Switch the Power Back On<\/h3>\n\n\n\n The pump is supposedly primed by now, but you need to check that it\u2019s working properly and empty out any trapped air. To do all this, you should reconnect the power, and turn on the pump. <\/p>\n\n\n\n
The air valve should blow out the excess air at first, and then it should spew out water. This means that your process is a success. Turn the air valve off if things are going as planned. If not, then you\u2019d need to repeat the previous steps once again. Finally, set the multiport valve to \u2018filter\u2019 instead of \u2018recirculate\u2019.<\/p>\n\n\n\n
Now the swimming pool pump should be fully primed and good to go! <\/p>\n\n\n\n <\/figure>\n\n\n\nFrequently Asked Questions (FAQs)<\/strong><\/h2>\n\n\n\nHere are some of the most common questions we often receive around properly priming swimming pool pumps, and our team’s best answers to them.<\/p>\n\n\n\n
What if the pump is still not working after carrying out all the priming steps?<\/h3>\n\n\n\n Usually, pumps can\u2019t start if they don\u2019t have enough water inside them or in the system around them. You can turn off the power and add more water to the pump, then try again.<\/p>\n\n\n\n
The pool pump loses power after a few hours, why is that?<\/h3>\n\n\n\n Mechanical systems can be stubborn if a single screw isn’t tightened the right way. Check the various components for leaks. Start with the lid, as the gasket o-ring can cause that leak. Or maybe the lid isn\u2019t tightened sufficiently.<\/p>\n\n\n\n
What do you do when everything looks fine, but the pool pump is still not working?<\/h3>\n\n\n\n The water level in the pool could be too low, so try to fill it up and see what happens. Or, there could be a leak in the piping connected to the pipe.<\/p>\n\n\n\n
As a last resort, you can solicit the services of a professional swimming pool contractor to locate the pump’s problem and fix it. <\/p>\n\n\n\n
Our Conclusion On How to Prime A Pool Pump<\/strong><\/h2>\n\n\n\nWe hope you enjoyed this guide on how to properly prime a swimming pool pump in 7 quick and easy steps. Priming a pool pump is an essential process to get the pool area up and running. Luckily, it\u2019s a simple task and doesn\u2019t require thorough technical skills.<\/p>\n\n\n\n
All that you need is a basic knowledge of working with electrical systems. This is critical for your safety, as well as the proper functioning of your machine.<\/p>\n\n\n\n
The goal is to get water inside the water pump and connected pipes, get the air out, clean up what needs cleaning, and inspect everything to make sure it\u2019s in a peachy state. It\u2019s just as simple as that!<\/p>\n","protected":false},"excerpt":{"rendered":"
A pool pump is just like the human heart that pumps life to the whole body, but you may be asking yourself “how do you prime a pool pump”. Your swimming pool pump is wholly responsible for carrying the water-purifying agents to the pool, renewing the water, passing it through the heater, and filtering out […]<\/p>\n","protected":false},"author":1,"featured_media":1082,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_genesis_hide_title":false,"_genesis_hide_breadcrumbs":false,"_genesis_hide_singular_image":false,"_genesis_hide_footer_widgets":false,"_genesis_custom_body_class":"","_genesis_custom_post_class":"","_genesis_layout":""},"categories":[1,5],"tags":[],"yoast_head":"\n
How to Prime A Pool Pump: Quick Guide (7 Easy Steps to Follow)<\/title>\n \n \n \n \n \n \n \n \n \n \n \n \n \n \n\t \n\t \n\t \n \n \n \n\t \n\t \n\t \n